Teradek Bolt 500 SDI/HDMI Video Transmitter And Two Receiver Set

Teradek Bolt 500 SDI/HDMI Video Transmitter And Two Receiver Set
Teradek Bolt 500 SDI/HDMI Video Transmitter And Two Receiver Set Teradek Bolt 500 SDI/HDMI Video Transmitter And Two Receiver Set Teradek Bolt 500 SDI/HDMI Video Transmitter And Two Receiver Set Teradek Bolt 500 SDI/HDMI Video Transmitter And Two Receiver Set Teradek Bolt 500 SDI/HDMI Video Transmitter And Two Receiver Set
$4,571.00
SKU
Mfr # 10-0938

Teradek Bolt 500 SDI/HDMI Video Transmitter and Two Receiver Set

Key Features 

  • Complete Bolt Set
  • Wirelessly transmit visually lossless 1080p60 Video/Audio up to 500 ft
  • < 0.001 seconds latency
  • Rapid Reconnect & Real-Time Frequency Adjustment
  • Built in HDMI/SDI Cross Conversion
  • Multicast up to 4 Receivers
  • Support camera metadata, timecode, and start/stop flags

The Bolt 500
With highly refined software, new wireless radios, and a redesigned chassis, these new models are the most reliable and capable monitoring solutions we have ever built. Metadata and timecode support, 3D LUTs, dual inputs/outputs, multicast capable (1 Transmitter can multicast up to 4 Receivers), manual frequency selection and USB 3.0 GRAB Engine are all included on these new models but with the following new features:

Longer Range
Transmit visually lossless video up to 500ft with no delay.

More Robust Than Ever Before
Reach your Bolt’s full range and potential right out of the box with new software that provides the most robust wireless link we’ve ever created.

Built-In HDMI to SDI Converter
Perfect for use with MoVI and other gimbals, Bolt’s TX has a built-in HDMI to SDI converter, allowing you to connect both your on-camera monitor and video source via the same device.

2 New DFS Channels
Operate interference-free more often in the USA and Europe by making use of two newly introduced DFS channels.

Rapid Reconnection
Reconnect times during a dropped link are now instantaneous once you move back into range.

Specs Table

Bolt 500 3G-SDI/HDMI Video Transmitter  
Video Inputs 1 x 75 Ohms BNC
1 x 75 Ohms BNC (loop-out)
Video Outputs 3G/HD/SD-SDI: 1 x BNC (75 Ohm)
Input / Output 3G-SDI/HDMI
Color Sampling SDI: YCbCr 4:2:2, 10-bit (8-bit when format conversion is enabled)
HDMI: RGB 4:4:4

In the Box

General
3 x HDMI 18in Cable (Type A to Type A)
3 x SDI (BNC to BNC) Cable 10 inch

Transmitter
1 x 2-pin Connector to PowerTap 18 inch Cable
1 x Hot Shoe Adapter (1/4"-20 inch)
1 x HDMI 18in Cable (Type A to Type A)
1 x SDI (BNC to BNC) Cable 10 inch
Standard Manufacturer's Warranty

Receiver
1 x Thumb Screw 1.25 inch length (1/4"-20 inch)
1 x Lightstand Adapter (1/4"-20 inch)
1 x SDI (BNC to BNC) Cable 10 inch
1 x USB 3.0 Cable A to Micro B (3ft Length)
1 x PSU 2-Pin Connector to 18W AC Adapter 6ft cable
Standard Manufacturer's Warranty

Receiver 2
1 x Thumb Screw 1.25 inch length (1/4"-20 inch)
1 x Lightstand Adapter (1/4"-20 inch)
1 x SDI (BNC to BNC) Cable 10 inch
1 x USB 3.0 Cable A to Micro B (3ft Length)
1 x PSU 2-Pin Connector to 18W AC Adapter 6ft cable
Standard Manufacturer's Warranty

Write Your Own Review
You're reviewing:Teradek Bolt 500 SDI/HDMI Video Transmitter And Two Receiver Set
Your Rating