Teradek Bolt 500 3G-SDI/HDMI Video Transceiver Set

Brands:
$3,100.00
SKU
Mfr # 10-0935

Teradek Bolt 500 3G-SDI/HDMI Video Transceiver Set

Key Features 

  • Complete Bolt Set
  • Wirelessly transmit visually lossless 1080p60 Video/Audio up to 500 ft
  • < 0.001 seconds latency
  • Rapid Reconnect & Real-Time Frequency Adjustment
  • Built in HDMI/SDI Cross Conversion
  • Multicast up to 4 Receivers
  • Support camera metadata, timecode, and start/stop flags

With highly refined software, new wireless radios, and a redesigned chassis, these new models are the most reliable and capable monitoring solutions we have ever built. Metadata and timecode support, 3D LUTs, dual inputs/outputs, multicast capable (1 Transmitter can multicast up to 4 Receivers), manual frequency selection and USB 3.0 GRAB Engine are all included on these new models but with the following new features:

Longer Range
Transmit visually lossless video up to 500ft with no delay.

More Robust Than Ever Before
Reach your Bolt’s full range and potential right out of the box with new software that provides the most robust wireless link we’ve ever created.

Built-In HDMI to SDI Converter
Perfect for use with MoVI and other gimbals, Bolt’s TX has a built-in HDMI to SDI converter, allowing you to connect both your on-camera monitor and video source via the same device.

2 New DFS Channels
Operate interference-free more often in the USA and Europe by making use of two newly introduced DFS channels.

Rapid Reconnection
Reconnect times during a dropped link are now instantaneous once you move back into range.

Specs Table

Bolt Pro 500 3G-SDI Video TX

 
Video Inputs 1 x SD/HD/3G-SDI (75 Ohm BNC)
Video Outputs 1 x HD/SD/3G-SDI Loop-out (75 Ohm BNC)
Color Sampling SDI: YCbCr 4:2:2, 10-bit (8-bit when format conversion is enabled)
Delay Tx To Rx <0.001sec (when no video format conversion is enabled)

Supported Resolutions

1080p 23.98 / 24 / 25 / 29.97 / 30 / 50 / 59.94 / 60
1080p sf23.98 / 24 / 25 / 29.97 / 30
1080i 50 / 59.94 / 60
720p 50 / 59.94 / 60
480p 59.94 / 576p 50 (via HDMI ports only)
480i (NTSC) / 576i (PAL)
Video Compression Visually lossless
Color Correction CDL/1024 1D LUT (supports 10-bit color)
33 x 33 x 33 3D LUT (supports 10-bit color)
Frequency Non-DFS Frequencies:
5.19 to 5.23 GHz
5.755 to 5.795 GHz

DFS Frequencies:
5.27 to 5.55 GHz
5.67 GHz
Channel Selection Auto
RF Power 17 dBm EIRP
Range Up to 500' (152 m)
Encryption AES-128
Audio Compression 48 kHz 24-bit PCM
Audio Input Embedded
Switches On/Off
Reset Switch
Application Bolt Manager Application for OSX & Windows
Noise Rejection Can coexist with Wi-Fi and 5 GHz cordless phones
Construction Milled aluminum (chassis) and regulation-compliant PCB
Plastic cap
Power Input Connector 2-pin 7 to 28 VDC
Power Consumption 7.3 W nominal @ 1080p
Operating Temperature 32 to 104°F (0 to 40°C)
Dimensions 1.0 x 2.6 x 4.0" (2.4 x 6.6 x 10.2 cm)
Weight 7.6 oz (217 g)
Bolt 500 3G-SDI/HDMI Video Receiver  
Video Outputs 1 x 75 Ohms BNC
1 x Micro-USB 3.0 female type B
1 x HDMI Type A female
Input / Output 3G-SDI/HDMI
Color Sampling SDI: YCbCr 4:2:2, 10-bit (8-bit when format conversion is enabled)
HDMI: RGB 4:4:4, 8-bit
Latency <0.001 seconds
Resolution 1080p60
Video Compression Visually lossless
Test Pattern Generator Custom output formatted test pattern over HDMI and SDI
Color Correction CDL/1024 1D LUT (supports 10-bit color)
33 x 33 x 33 3D LUT (supports 10-bit color)
Frequency Non-DFS Frequencies:
5.19 to 5.23 GHz
5.755 to 5.795 GHz

DFS Frequencies:
5.27 to 5.55 GHz
5.67 GHz
Channel Selection Auto
RF Power 15 dBm EIRP
Range Up to 500' (152 m)
Encryption AES-128
Audio Compression 48 kHz 24-bit PCM
Audio Input Embedded
Switches On/Off
Reset Switch
Application Bolt Manager Application for Mac OS X & Windows
Power Input Connector 2-pin 7 to 28 VDC
Power Consumption 9 W nominal @ 1080p
Operating Temperature 32 to 104°F (0 to 40°C)
Dimensions 1.0 x 3.5 x 5.8 (25.2 x 88.9 x 146.5 mm)

In the Box

General
2 x HDMI Type A to Type A 12in Cable
2 x SDI BNC to BNC 10in Cable

Transmitter
1 x 2-pin Connector to PowerTap 18 inch Cable
1 x Hot Shoe Adapter (1/4"-20 inch)
1 x HDMI 18in Cable (Type A to Type A)
1 x SDI (BNC to BNC) Cable 10 inch
Standard Manufacturer's Warranty

Receiver
1 x Thumb Screw 1.25 inch length (1/4"-20 inch)
1 x Lightstand Adapter (1/4"-20 inch)
1 x SDI (BNC to BNC) Cable 10 inch
1 x USB 3.0 Cable A to Micro B (3ft Length)
1 x PSU 2-Pin Connector to 18W AC Adapter 6ft cable
Standard Manufacturer's Warranty